3 Ways to Start a Motorcycle

Table of contents:

3 Ways to Start a Motorcycle
3 Ways to Start a Motorcycle

Video: 3 Ways to Start a Motorcycle

Video: 3 Ways to Start a Motorcycle
Video: How To Ride A Motorcycle In 60 Seconds!! 2024, March
Anonim

Learning how to start a motorcycle is essential for anyone who owns one. This shouldn't be difficult if the machine is in good condition, so read on to learn the basics of powering it up!

Steps

Method 1 of 3: Taking the Initial Steps

Start a Motorcycle Step 1
Start a Motorcycle Step 1

Step 1. Determine if the bike is carbureted or has electronic fuel injection

Many motorcycles, especially older and cheaper ones, do not have modern fuel injection systems. To clear up the doubt, look for the choke lever, which will likely bear the inscription "Choke" and will be on the left side of the handlebars, above the horn. Carbureted motorcycles will have this lever, unlike those that have electronic injection.

Image
Image

Step 2. Get on the motorcycle when starting it

This will give you full control over the machine after startup. If you need to start the bike without getting on it, remember to put it in neutral (which is usually between first and second gear) before starting the engine so it doesn't run around without you!

Start a Motorcycle Step 3
Start a Motorcycle Step 3

Step 3. Check that the motorcycle is in good working condition

It should have enough fuel and battery. In addition, it is important to keep it up to date, especially in damp or cold places. Installing new spark plugs or cleaning and adjusting the opening of old ones is good maintenance. Also check the engine timing, adjusting it if necessary. Carburetor maintenance and cleaning can also help a lot.

Replace spark plug wires if they are old or frayed. When changing, use only the products recommended by the manufacturer, which can be found in the vehicle manual

Image
Image

Step 4. Check the oil level

Remember to check the oil level to make sure the engine is well lubricated before starting it. This goes for any vehicle. Do not start the engine if the level is low or if there is no oil, as this will cause overheating and then the engine to break down.

Start a Motorcycle Step 5
Start a Motorcycle Step 5

Step 5. Check the battery

Place the key in the ignition and turn it clockwise until the lights come on. If not, the problem is likely to be the battery, which will need to be replaced.

Method 2 of 3: Starting a Carbureted Motorcycle

Start a Motorcycle Step 6
Start a Motorcycle Step 6

Step 1. Look for the choke lever or power cutter button

To start a motorcycle with a cold engine, it will usually be necessary to use the choke or the "cut-off" button. The function of the choke, which is a lever that connects to the carburetor of some motorcycles, is to make the fuel mixture richer so that the engine can be started after not running for a few hours. The dirtier the carburetor and the colder the engine, the more this lever will need to be actuated.

  • It is not necessary to use the choke when the engine is hot, as in these cases the amount of energy needed to make it work again is less. All you have to do is press the accelerator a little while turning on for it to work normally.
  • Many bikes have a power cut button on the jack, so remember to put it away before starting the bike. However, leaving the motorcycle in neutral will disable the jack's power cutter.
Image
Image

Step 2. Operate the choke lever and leave the chain cutter in the "on" position

Also, do not touch the accelerator when operating the starter or ignition pedal so that the engine does not “choke”. Remember if; it is generally not necessary to engage the choke if the engine has been used in the last few hours.

Image
Image

Step 3. Turn ignition to "on" position

The dashboard lights should come on and the neutral indicator should appear on the display (if you followed the recommendation to leave the bike in neutral).

Image
Image

Step 4. Start the engine

Engage the clutch (on the left side) and press the ignition button (on the right side). You should now hear the pleasant starting sound of the bike.

Image
Image

Step 5. Close the choke lever and apply the throttle a little

Do this right after the engine starts, accelerating progressively as the engine warms up. You may need to leave the choke on for a while longer, but turn it off as soon as possible so the bike runs smoothly. Do not make the engine rev too high while it is still warming up.

Method 3 of 3: Starting a Motorcycle with Electronic Fuel Injection

Image
Image

Step 1. Put the motorcycle in neutral

Generally, the position that selects it is between first and second gears.

Start a Motorcycle Step 12
Start a Motorcycle Step 12

Step 2. Don't worry about the choke

Motorcycles with electronic injection automatically manage the right amount of fuel to be injected into the engine, whether in the cold or in the heat. There is no choke on these bikes, just accelerate a little when you start them.

Image
Image

Step 3. Engage clutch

It is usually on the left side. Many bikers also apply the front brake (on the right side of the handlebars) at this time.

Image
Image

Step 4. Press and hold the ignition button

It is usually on the right side, just below where your right hand is while riding.

Image
Image

Step 5. Try to speed up a bit

Do this if the bike does not start this first time, but remember to leave the clutch fully engaged first.

Recommended: