How to Sew a Button (with Images)

Table of contents:

How to Sew a Button (with Images)
How to Sew a Button (with Images)

Video: How to Sew a Button (with Images)

Video: How to Sew a Button (with Images)
Video: How to Unwrinkle a Wrinkled Paper 2024, March
Anonim

Button sewing is very easy once you get the hang of it. This is a very useful skill to possess, as the buttons always fall off.

Steps

Method 1 of 2: Two Holes

Sew a Button Step 1
Sew a Button Step 1

Step 1. Choose the button and the line

Select a suitable button and a thread that matches the button, clothing, and any thread used to sew on the other buttons. If desired, you can fold the line in half to make the task faster.

Image
Image

Step 2. Thread the needle

Simply pull the thread through the needle until both ends are the same length.

Image
Image

Step 3. Tie a knot at the end of the thread

One way to tie a knot is to wrap the thread around your finger as shown, roll the thread between your fingers and pull it tight. If you have bent the thread, tie the ends together. Leave a long piece of thread, whether it's just a thread or two.

Image
Image

Step 4. Position the button on the fabric

Align the button with the other buttons on the piece. Check the buttonhole. Bring the buttonhole side of the fabric together and make sure the button lines up with your buttonhole.

Image
Image

Step 5. Push the needle with the thread through the fabric and through one of the button holes

Pull the line out completely.

Image
Image

Step 6. Attach a safety pin

Place a pin under the button, between the stitch you made and the place where the next one goes, preventing the stitch from getting too tight. Then push the needle through the next hole and through the fabric. Pull the entire line through the hole. It's best to hold the button so it doesn't move.

Image
Image

Step 7. Repeat the process

Pass the needle through the first hole and pull the thread completely through the fabric.

Image
Image

Step 8. Attach the button

Repeat the process as many times as necessary until the button is firmly locked in place.

Image
Image

Step 9. At the last stitch, push the needle through the material, but not through the hole in the button

Image
Image

Step 10. Remove the pin

Image
Image

Step 11. Wind the line

Do this six times around the line between the button and the fabric to reinforce the stitch you made.

Image
Image

Step 12. Pull the needle down through the fabric

Image
Image

Step 13. Make three or four ends to secure the thread

Make a few stitches below the button, going back and forth to fortify them. Make a full stop.

Image
Image

Step 14. Cut off excess

Method 2 of 2: Four holes

Sew a Button Step 15
Sew a Button Step 15

Step 1. Choose what you are going to use

Select a suitable button and a thread that matches the button, clothing, and any thread used to sew on the other buttons.

Image
Image

Step 2. Thread the needle

Simply pull the thread through the needle until both ends are the same length.

Image
Image

Step 3. Tie a knot at the end of the thread

One way to tie a knot is to wrap the thread around your finger as shown, roll the thread between your fingers and pull it tight. If you have bent the thread, tie the ends together. Leave a long piece of thread, whether it's just a thread or two.

Image
Image

Step 4. Position the button on the fabric

Align the button with the other buttons on the piece. Check the buttonhole. Bring the buttonhole side of the fabric together and make sure the button lines up with your buttonhole.

Image
Image

Step 5. Push the threaded needle through the fabric and one of the button holes

Pull the thread completely at each stitch.

Image
Image

Step 6. Attach a safety pin

Place a pin under the button, between the stitch you made and the place where the next one goes, preventing the stitch from getting too tight.

Image
Image

Step 7. Push the needle through the diagonal opposite hole and through the fabric

Pull the line out completely.

Image
Image

Step 8. Repeat the action twice for these holes, then move on to the other two holes

Image
Image

Step 9. Swap through the opposite pairs until the button is firmly attached

Image
Image

Step 10. At the last stitch, push the needle through the material but not through the hole in the button

Image
Image

Step 11. Remove the pin

Image
Image

Step 12. Wind the thread

Do this six times around the line between the button and the fabric to reinforce the stitch you made.

Image
Image

Step 13. Pull the needle down through the fabric

Image
Image

Step 14. Make three or four ends to secure the thread

Make a few stitches below the button, going back and forth to fortify them. Make a full stop.

Image
Image

Step 15. Cut off excess

Image
Image

Step 16. Ready

Tips

  • Fold the thread in half if you want to reduce the number of times you need to thread the thread through the holes to secure the button.
  • Keep the back of the knob as aligned as the front, making sure you're not creating a clump of thread. Bring the line in and out through the same area.
  • For buttons that will be used a lot, try to tightly wrap the long part of the needle thread around the thread that holds the button 4 or 5 times, then force the needle and thread through the mound of thread you created. needle parallel to the button hole, avoiding resistance. Use a thimble when pushing the needle (the reason for this is simple: the exposed thread will make the button fall out soon unless you wrap the exposed threads with some protection.) Once the needle is through, push back into the garment and tie with the longest thread you left in the starting knot. When you wind the threads, the button is more secure, and the thread that holds it in place lasts longer.
  • If you are replacing a four-hole button, look to see how the other buttons are attached to the fabric. Use the same pattern on the stitches (cross or parallel) used on the other buttons.
  • It might also be a good idea to try to match the color of the thread used on the other buttons. Some stores specialize in buttons, and if they don't have the exact button you lost, they must have something very close to it. If you don't want to wear something that looks similar, consider changing all the buttons so your outfit will look much better.
  • You can use two pieces of needle thread by bending them and thus using four threads at the same time, which really speeds up the process.
  • Make sure you use at least 13 cm of line.
  • Some people prefer to attach the button to their clothes with a few stitches before they actually start to sew the button on.
  • Ordinary line is good, but there is such a thing as a button line. It is thicker and stronger than the common one. If the button you are sewing needs reinforcement, such as a jacket, try button thread.
  • Another way to knot the thread at the end is to tie a small stitch in the back, pull until the back almost touches the fabric and then thread the needle through the loop before pulling out definitively. If you do this twice in the same place, you will have made a double knot. Finally, cut the line next to the knot.

Recommended: