Most Pandora bracelets have a specific type of snap clasp called a barrel clasp. It's firm, but not difficult to open with your fingers or a clasp opener. The stopper beads that protect the ends of these bracelets open in the same way. When you want to wear your bracelet again, lock the clasps.
Steps
Method 1 of 4: Opening the bracelet with your fingers
Step 1. Rotate the lock until the groove is facing up
Twist the clasp with your fingers until you see a vertical line from end to end along one side. This line is where the clasp opens.
The standard clasp has a groove. Pandora also sells some lobster-like ones, which are like hooks, where you drag the lever down to open the clasp and slide the end of the bracelet out
Step 2. Insert the nails into the groove
Fit your toe nail first, then another if you can. The easiest way to do this is with both thumbs, but you can also use the other fingers. Position them so that the two nails are with the surfaces touching each other.
- Support the sides of the clasp with your other fingers or your body.
- Once you get used to opening the bracelet, you'll be able to open it with just one nail, but starting with two is easier and offers better leverage.
Step 3. Separate the sides of the clasp until it opens
Use your nails to push the sides of the clasp outward in opposite directions, applying a little pressure. The clasp will open and you can remove or put on the bracelet.
- The clasp can be a little stiff and difficult to open, and this is so that the bracelet doesn't accidentally come loose while you're wearing it. Apply a little more pressure to open it without having to use a tool.
- If you have problems opening, adjust the grip and try again. Most open without too much trouble, but you might need a clasp opener to remove one that's stuck.
Step 4. Lift the stem to release the ends of the bracelet
The clasp is attached to one end of the bracelet and the other looks like a small plug. Pick it up and take it out of the socket to finish opening the bracelet.
Method 2 of 4: Using a Closure Opener
Step 1. Hold the opener between your thumb and forefinger
Close your hand as if making a fist. With the other hand, place the clasp over the index finger and hold it in place with your thumb. Position it so the straight edge points away from your body.
- Pandora sells a clasp opener that looks like a flower pendant. It has four petals with straight edges that can be used to open clasps.
- If you don't have a Pandora opener, use a generic, jewelry or phone tool. You can also use small coins or other sturdy objects with a smooth edge.
Step 2. Rotate the lock until you see the groove
Twist the clasp with your fingers until the gap is up. It is a vertical opening that goes from one edge to another. Position the slot at the best angle to fit the opener.
Step 3. Insert the opener into the slot
Fit the edge of the opener into the slit and push the side until it opens, but avoid forcing.
Hold the clasp firmly between your fingers or rest it against your side
Step 4. Open the clasp to remove the bracelet
Move the opener back and forth, pushing it against the sides of the clasp. Apply constant pressure and it should open without too much difficulty. Then pull the loose end of the bracelet to finish loosening.
- If you can't open it all at once, hold it a different way. Grasp it firmly and tilt it slightly to fit snugly into the opening.
- The bracelet is attached to the clasp at one end, so find the one that is loose and take it off with your fingers.
Method 3 of 4: Closing the bracelet
Step 1. Place the end of the bracelet on the open clasp
Look at the ends of the bracelet and find the end that has a small metal rod. Open the clasp and support the rod on the bend, pushing it as far as possible.
- The easiest way to put on the bracelet is to rest it on your wrist. Place clasp on top and loop around wrist with tip, engaging rod.
- If it doesn't go in fully, the bracelet will not close properly and could end up falling off. Position the rod carefully when locking the clasp.
Step 2. Hold the sides of the clasp with your fingers
Place your thumb on one side and forefinger on the other, holding it firmly between your fingers.
Use your free hand or fingers to hold the bracelet in place while locking
Step 3. Bring the sides of the clasp together to lock it
Bring your thumb and forefinger together to close the bracelet, without using too much force. Give the end of the rod a little tug to see if it fits snugly inside. If it feels loose, open and adjust again.
Avoid forcing the clasp if it doesn't lock properly, as it could break. The rod may not be seated properly in the groove, so open it carefully and try again
Method 4 of 4: Opening and Closing Clip Accounts
Step 1. Rotate the wrist strap so that the notch is facing up
The clip bead will be at the end of the bracelet, just after the rod that closes the bracelet. Turn the bead with your fingers until you see the groove, a thin line running down the side of the bead.
- Please remember that you need to open the bracelet before opening the account. This allows it to prevent others from slipping out.
- The account is very similar to the closing, as they use the same mechanism.
Step 2. Fit your thumbnail into the opening
You can usually open the account with a fingernail, but if you need more leverage, try using your other thumb to pull the other side in the opposite direction.
- If you are wearing the bracelet, hold it with the fingers of your other hand to keep it firmly in place.
- You can also use a clasp opener or a thin coin.
Step 3. Open the account and set it aside for now
Use constant, even pressure to pull the sides apart. The remaining beads will be loose, so hold the end of the bracelet, keep it pointed up, and carefully remove the other pendants you want to remove.
Once the account opens, you can remove it from the bracelet. Be careful not to drop the others
Step 4. Hold the bead between your fingers and place it around the bracelet
Grasp it between your thumb and forefinger, keeping the opening facing up. With the other hand, grasp the end of the bracelet and place it inside the socket, supporting the shaft in the curvature.
Hold the other pendants with your other fingers or press them against a flat surface or your wrist so they don't move
Step 5. Snap the sides to close
Bring your fingers together and press without too much force. When it closes, you will hear a "click".
If it doesn't close properly, don't force it. Open it again and check the alignment. The cord may not fit inside the bead
Tips
- Avoid rolling the bracelet off your wrist. Always try to open the clasp when you want to remove it so that the cord doesn't break or widen.
- Always make sure the account is closed before putting on the bracelet.
- Be careful when opening the bracelet and account. Nothing will be holding the pendants in place and they could fall off.
- Opening and locking the clasps does not require much force. If you have difficulties, take a look before it does not spoil.
- Do not force the latch latch or it may break.
- If the clasp is difficult to open or does not close properly, take the bracelet to a Pandora store and ask if it is possible to change the pendant or repair it.