3 Ways to Hang a Blink on a Brick Wall

Table of contents:

3 Ways to Hang a Blink on a Brick Wall
3 Ways to Hang a Blink on a Brick Wall
Anonim

Hanging blinkers is one of the simplest and coolest ways to decorate a brick wall during Christmas! And you can do this in several ways without damaging the material: you can use a hot glue gun if you want a simple and practical option; if you prefer a safer alternative, buy individual snap clamps; finally, if you are looking for a more permanent option, get the drill and some bushings and install hooks! Follow the tips in this article to give your home a Christmas look.

Steps

Method 1 of 3: Using a Hot Glue Gun

Hang Christmas Lights on Brick Step 1
Hang Christmas Lights on Brick Step 1

Step 1. Buy a medium sized flasher

Go to a decorative items store and choose a flasher that has a medium-sized base. This facilitates glue application and wall installation. While those common blinkers (from Christmas trees, for example) are cute, they don't hold quite so firmly on the bricks.

  • Another cool option is to buy a flasher with detachable bulbs. This way, you can unscrew each one at installation time to avoid breaking anything.
  • If you like smaller flashers better, install snap hooks or clips to make the project more secure. Just read one of the next methods.
Hang Christmas Lights on Brick Step 2
Hang Christmas Lights on Brick Step 2

Step 2. Place a tube of glue in the gun and turn it on

Install a tube of hot glue on the gun, turn it on and wait two minutes while it heats up. Use an extension cord if you want to install the flasher at a higher point on the wall. When the material is at the right temperature, squeeze the trigger lightly and see if the glue comes out of the tip.

Be careful when operating the hot glue gun. Do not place it near any flammable surface and, if possible, wear heavy gloves

Hang Christmas Lights on Brick Step 3
Hang Christmas Lights on Brick Step 3

Step 3. Apply a string of glue to the base of a flasher bulb

Hold the gun tip very close to the plastic lamp base and squeeze the trigger lightly until the glue comes out. Apply it in a 2, 5 cm thick fillet on the material.

  • Don't let the glue drip onto the lamp or flasher cord. Just run it on the plastic base.
  • You can also apply a drop of glue under the base of each flasher socket. Thus, the lamps will be perpendicular after installation.
Hang Christmas Lights on Brick Step 4
Hang Christmas Lights on Brick Step 4

Step 4. Press the plastic base against the brick for about 20 seconds

Place the lamp base against the wall and apply force while the glue dries. Make sure it's stuck together and doesn't wobble. If it rocks, pull it out and put more glue on the plastic.

  • Apply some glue to the top of the base, wait a while and see if the lamp becomes sturdier.
  • The glue will start to dry in a few seconds, but wait until the lamp is steady before moving on to the next one or turning on the blinker.
Hang Christmas Lights on Brick Step 5
Hang Christmas Lights on Brick Step 5

Step 5. Apply glue to the base of the other bulbs

Repeat the process with all other blinker lamps. Install each one in such a way that the cord that holds them is more or less loose, or any false movement will create the risk of dismantling the entire installation.

  • On the other hand, the blinker cord should not be too loose - or it could generate pressure and even fall off the wall.
  • The first base you glued on will serve as a reference point for the entire project, but be careful not to accidentally pull the piece.
Hang Christmas Lights on Brick Step 6
Hang Christmas Lights on Brick Step 6

Step 6. Rub isopropyl alcohol on the bricks when you want to remove the flasher

You can try to remove the lamps from the wall with a little force, but don't insist too much: if they show resistance, moisten a cotton swab in isopropyl alcohol and pass around the plastic bases. This will gradually loosen the glue.

  • Buy isopropyl alcohol at any drugstore.
  • The alcohol will melt the glue in no time. If that's not enough, try running a metal scraper between the base and the brick.
  • You can also use isopropyl alcohol to undo any mistakes when installing the lamps. Just wait for the glue to dry and the plastic base to cool.

Method 2 of 3: Using Pressure Clamps

Hang Christmas Lights on Brick Step 7
Hang Christmas Lights on Brick Step 7

Step 1. Check if the bricks have a 3 mm relief in relation to the grout

You will only be able to follow this method if the bricks detach from the wall by about 3 mm. Before proceeding with the project, take this measurement using a ruler or measuring tape.

Hang Christmas Lights on Brick Step 8
Hang Christmas Lights on Brick Step 8

Step 2. Measure the height of individual bricks to choose the best cleats

Pressure clamps are made to stay on individual bricks, but it all depends on the size of the pieces: 6 cm, 7 cm, and so on. When in doubt, always opt for accessories a little bigger than what you think is necessary.

  • If there is no room for staples on the wall, use another of the methods listed in this article: use a hot glue gun or install hooks with a drill.
  • You also have the option of choosing a more affordable place to install clips and hang the flasher.
Hang Christmas Lights on Brick Step 9
Hang Christmas Lights on Brick Step 9

Step 3. Estimate the space you intend to cover with the flasher

Choose a nice place for you to install the flasher, such as the top of a wall or around a door. Then use a ladder and a measuring tape to determine the distance you want to cover. You will have a clearer idea of the size of the flasher and the amount of pressure clamps.

  • In general, you need to install each clip 15 to 20 cm apart.
  • For example, if you want to hang a three foot blinker, use about six snap clips (but be prepared to use more or less than that).
  • If you don't mind leaving the flasher a little loose on the wall, spread the clips even further apart. It all depends on your home decor style!
Hang Christmas Lights on Brick Step 10
Hang Christmas Lights on Brick Step 10

Step 4. Start installing each clip from the underside of the bricks

Each pressure clamp sits on top of an individual brick. Usually, the base of the piece has a "U"-shaped spring. You just need to fit it to the underside of the brick and use some force.

Regardless of the size of the bricks, the spring is against the grout between them (provided the clamp as a whole is big enough)

Hang Christmas Lights on Brick Step 11
Hang Christmas Lights on Brick Step 11

Step 5. Finish installing each clamp through the top of the bricks

In general, the tops of the clamps have some bulges that attach to the bricks (also on the grout). Finish snapping in this area and tighten lightly to see if the part is secure.

You don't need to use any extra pieces to secure the wall clamps. They'll get fixed on their own

Hang Christmas Lights on Brick Step 12
Hang Christmas Lights on Brick Step 12

Step 6. Hang the blinker on the clips

Each clamp has two or more hooks that you can thread the flasher string through. Simply extend the material from one piece to the other, leaving the lamps suspended in the middle. Just be careful not to let the blinker loose, or it could fall out.

Step back and take a look at the flasher to see if it looks nice on the wall. Make any necessary adjustments before proceeding

Hang Christmas Lights on Brick Step 13
Hang Christmas Lights on Brick Step 13

Step 7. Press the bottom springs when removing the clips

When it's time to remove the decorations from the bricks, start by taking the blinkers off the hooks. Then squeeze the underside of each clamp to remove the parts.

  • If you are unable to remove any of the clamps, force against the spring using a small screwdriver.
  • These snap clamps stand up well to weather conditions (rain, sun, wind, etc.), but you'd better uninstall them all when the weather warms up to preserve the material longer.

Method 3 of 3: Installing Permanent Hooks

Hang Christmas Lights on Brick Step 14
Hang Christmas Lights on Brick Step 14

Step 1. Take measurements and mark the points where you intend to hang the flasher

Choose an interesting place to hang the flasher, such as around a door or window. Then take a ladder and a tape measure to decide where each light bulb will go and mark those points with chalk. You will have to drill all of them to install dowels and hooks. Place each one no more than 30 cm away from the others.

You will only know what the ideal flasher size is after calculating the distance you intend to cover with it

Hang Christmas Lights on Brick Step 15
Hang Christmas Lights on Brick Step 15

Step 2. Buy dowels to install the hooks on the wall

Bushings are those little plastic tubes installed in holes drilled in walls. As Christmas flashers are not heavy, you can buy small pieces. After drilling the holes in the bricks and inserting the dowels, all that's left is to put the hooks in place and move on to decorating.

  • Buy bags of dowels at any building supply store.
  • There are bushings of various sizes, each made to support different weights. Don't buy big pieces, or they will be too obvious on the wall.
Hang Christmas Lights on Brick Step 16
Hang Christmas Lights on Brick Step 16

Step 3. Install a 5mm drill bit into a drill

Rotate the current bit counterclockwise to remove it, then install the new one in the opposite direction. Choose a piece that is made for drilling bricks, remembering that it should be the same size as the dowels and hooks.

Ideally, the drill should be 5 mm. You can use a different part, as long as you also adapt the size of the bushings

Hang Christmas Lights on Brick Step 17
Hang Christmas Lights on Brick Step 17

Step 4. Drill the marked points with the drill

Put on personal protective equipment, such as goggles and a mask, so as not to injure yourself with possible grout splinters. Then go up the ladder and start punching each point you chalked up. Hold the drill tightly so it doesn't slip out of your hand and get out of control.

  • If possible, also wear gloves and long-sleeved clothing.
  • Remember that the drill can end up hitting a pipe in the wall. Be very careful and if you don't want to risk it, use one of the above methods.
Hang Christmas Lights on Brick Step 18
Hang Christmas Lights on Brick Step 18

Step 5. Install a plug in each hole in the wall

Take the bag of dowels you purchased and install one in each hole in the wall. Thread the pieces all the way to the base, rotating them if necessary, so as not to leave any exposed ends.

  • As stated above, you can buy the bushings at any building supply store.
  • If the bushings are not going in, tap the end of them lightly with a hammer. Don't use too much force as they are plastic and can break.
Hang Christmas Lights on Brick Step 19
Hang Christmas Lights on Brick Step 19

Step 6. Install a hook on each bushing

You will need hooks 2mm in diameter and the same length as the dowels. To install these parts, simply turn each one clockwise by hand. The flasher will be suspended from them.

The hooks have to be about the same dimensions as the bushings, or they won't fit inside them. Insert each piece to the bottom

Hang Christmas Lights on Brick Step 20
Hang Christmas Lights on Brick Step 20

Step 7. Hang the blinker on the hooks

Hang the flasher string on each hook you installed on the wall. If necessary, place plastic ties or pieces of tape at some points in the material to prevent it from slipping out of place. Done: enjoy the special decoration for Christmas!

  • Buy cable ties or ribbon rolls in black or in a shade that doesn't clash with the blinker theme.
  • Wrap the cable ties and tape around the cord, not the bulbs. Don't forget they are delicate.

Tips

  • Before hanging the flasher, plug it in and see if it's working so you don't spend time decorating for nothing.
  • See if the blinker is in full condition even after installation. Buy another if the current one has any more serious damage to the cord or lamps.
  • If you are going to hang the blinker on an exposed wall, buy a string that will resist contact with water (in case it rains).
  • Find a way to hide the extension (if you use one)! This is essential not only for aesthetic reasons, but also for safety.

Notices

Popular by topic